What Size AC Do I Need in Savannah, GA?

What Size AC Do I Need in Savannah, GA?

Savannah’s summer comfort problem is not just a high thermostat reading. Humid air can leave a house sticky even after the temperature falls, while a sun-exposed upstairs bedroom can lag behind the rest of the building. Neither symptom automatically calls for a bigger condenser. An AC size for a Savannah home should come from measured room heat gains, an explicit moisture load, equipment performance at local design conditions, and ducts that deliver the specified airflow. The city’s coastal setting also makes the placement and drainage of the equipment worth planning carefully.

The Savannah station and its limits

NOAA/NCEI’s 1991–2020 monthly normals for Savannah International Airport, USW00003822, show a July average high of 92.3°F, a July average low of 73.7°F, and 5.75 inches of normal July precipitation. The station is approximately 7.8 miles from the Census internal place point for Savannah. The National Weather Service Charleston office also publishes Savannah climate products. Those official records establish local summer heat and rainfall but do not give the design dry-bulb and moisture conditions for every Savannah address.

A home closer to the waterfront and one farther from it may experience different afternoon conditions. The contractor should state which weather source and design values were used and why they fit the property. Do not substitute the Charleston City station simply because the two cities share a coastal weather office. Likewise, Savannah’s airport record is not an excuse to assume that a heavily shaded downtown building has the same room solar load as an unshaded house elsewhere.

Two Savannah houses of equal area can have opposite needs

A shaded older home may have low afternoon solar gain through protected windows but substantial infiltration through the attic, floor, or exterior doors. A newer open-plan home can be tighter yet carry large sensible gains from west glass and roofing. Square footage does not identify those tradeoffs. Walk the conditioned boundary and record wall and ceiling constructions, insulation, window area, orientation, shade, equipment heat, occupancy, and intentional outdoor-air supply before any tonnage is proposed.

Porches and room conversions require particular care. A former porch with extensive glazing can peak sharply when exposed to sun, and its duct branch may be an afterthought. If the project will include insulation or window changes, calculate the existing and final arrangements separately. A system selected for an unfinished renovation can become too small before the work is done or too large after an improvement reduces load. Put the assumptions in writing so owner and installer are discussing the same building.

Keep the sensible and latent calculations visible

ACCA Manual J calculates cooling loads room by room. Its sensible component addresses temperature gain from the envelope, sun, and interior sources. The latent component addresses moisture introduced by occupants, cooking, ventilation, and humid air leakage. Savannah’s warm, rainy summer makes a latent result important, but the actual number depends on the home’s air paths and chosen design conditions. Ask for the room sensible schedule and the whole-house sensible, latent, and total loads rather than an unexplained final tonnage.

Investigate where unconditioned air may enter. Return duct leaks, ceiling penetrations, and an improperly connected crawlspace can add moisture and undermine the cooling system. These defects should be repaired, not treated as acceptable “fresh air”. Controlled ventilation should be designed and included in the load; accidental infiltration should be reduced where practical. If the house feels damp despite a cool thermostat, a leak or airflow problem may explain the complaint more directly than a capacity shortage.

Choose a matched system with Manual S

Manual S takes the load result into equipment selection. Require the exact outdoor unit, indoor coil, and blower match plus the manufacturer’s expanded performance data at the chosen Savannah outdoor and indoor conditions. Check whether the selected combination can cover the home’s temperature-changing demand and its full moisture-inclusive cooling demand as separate figures. The nominal tonnage printed in an equipment name does not specify either at a hot, humid design point. Airflow settings change coil behavior, so the proposed setting should be consistent with the selected performance row.

A substantially oversized AC can satisfy the thermostat early, cycle off, and lose the runtime needed for moisture removal and even room delivery. An undersized AC can fall behind at the stated design point despite clean components and proper airflow. The presence of a long run does not prove undersizing; near design weather, a correctly selected system may operate steadily. Compare actual temperature, humidity, and delivered air against the designed conditions before declaring that the number of tons is wrong.

Distribution may set the practical limit

ACCA Manual D connects each room’s load to a supply and return duct route. Savannah homes with ducts in vented attics or vulnerable underfloor spaces need inspection for leakage, insulation, crushing, and airflow restrictions. A long branch to a top bedroom can underdeliver while the central thermostat is already satisfied. Ask for room airflow targets and whether existing returns function with normal door positions. A larger condenser will not send air through a duct that is too small or disconnected.

Commissioning should include external static pressure, total airflow, and room delivery where problems have been identified. HVAC discussions may cite 350, 375, 400, or 450 cfm per nominal ton, but there is no universal Savannah setting among them. The manufacturer’s matched data, coil limits, sensible/latent balance, and actual duct pressure control the choice. Low airflow can affect coil operation; high airflow can alter moisture control. Document both the setting and the measured result.

Placement, condensate, and local project review

Savannah’s Development Services Department handles permit and inspection services for new construction inside city limits and provides a starting point for building work. Confirm what approval applies to a mechanical replacement or relocation at the actual address. City information also describes flood-protection requirements for qualifying new or substantially improved buildings in designated hazard areas. That should trigger an address-specific equipment-placement and permit conversation, not a blanket claim that every AC replacement requires the same elevation work.

Condensate drainage deserves a deliberate plan in a humid climate. Confirm the drain route, trap where applicable, overflow protection, access for cleaning, and whether a secondary safeguard is needed for the location. A wet ceiling or leaking pan is not evidence that the unit needs a different tonnage. Keep drainage, electrical, refrigerant, and duct work in the project scope so the equipment match can be commissioned safely and serviced later.

Evaluate a Savannah proposal by its evidence

Ask which rooms peak when the sun hits them, whether ducts in unconditioned spaces were tested, and how infiltration was estimated. Request the Manual J inputs and separate latent load, expanded Manual S capacity, and any Manual D corrections. Ask for the weather station name, not just a generic “Georgia” climate setting. Finally, ask what indoor humidity and room temperature readings will be checked at handover and how the contractor will diagnose a later comfort complaint.

The most defensible Savannah AC size is not a product label borrowed from the old system. It is the equipment combination whose delivered sensible and total capacity supports the actual room and moisture loads at a documented local design point. Its ducts, return paths, condensate handling, and placement must also suit the building. Those practical details can matter as much to comfort as a nominal half-ton difference.

If one bid offers a smaller system than another, compare the underlying building inputs before treating the lower figure as risky. Are the attic insulation and window ratings verified? Did one bidder assume a sealed return while the other included an existing leak? Did both use the same indoor design setpoint and local weather conditions? A disagreement in tonnage can stem from these assumptions rather than from the equipment brand. Resolve the assumptions and repeat the load comparison; otherwise the apparent choice between two sizes is really a choice between two different imagined houses.

Related Cooling Load Guide resources

Official and technical sources

Similar Posts