What Size AC Do I Need in Wichita, KS?

What Size AC Do I Need in Wichita, KS?

At the doorway between a Wichita house and its enclosed sunroom, an opening is often expected to do two jobs it was never designed to perform: deliver comfort and carry return air. A warm addition with one field-added supply does not automatically prove the central unit is small. It may show that a new thermal boundary was never calculated and a complete air circuit was never built.

The remedy begins by treating the addition surface by surface. West glass, slab edge, roof, infiltration and shade establish its room load. The combined corrected loads then inform equipment selection, while a duct analysis decides whether the original trunk can spare the required air without starving bedrooms. A deliberate return route completes the addition; extra condenser capacity cannot complete it.

This Wichita, Kansas authoring file addresses city-qualified sizing for a glass-heavy addition that needs its own thermal-boundary, return-air and trunk-capacity analysis.

Treat the sunroom as a new load and a new air loop

Draw the addition as its own zone of surfaces before merging totals. Confirm which walls became interior, how the old exterior opening is configured, and whether the door remains. Identify the supply register and every plausible return path. The sunroom’s floor area is only one geometric fact; glass ratio, orientation and boundary details often control its behavior and peak timing.

The old exterior wall deserves a boundary audit after enclosure. Portions that remain outside-facing, enclosed cavities and the widened opening can each have different load treatment. A sketch with surface labels is safer than assuming the entire wall disappeared, particularly when the addition roof and slab meet the original structure imperfectly.

Use Wichita normals without converting averages into a design day

Wichita station normals demonstrate both heating and cooling seasons and a notable July day-to-night range. They do not specify the design day or the sunroom’s glass gain. Use an approved design condition consistently in Manual J. Treat the normal range as narrative context, not permission to reduce or increase capacity without modeling the actual construction.

The approved NOAA/NCEI 1991–2020 Monthly Normals — WICHITA, KS US identifies WICHITA, KS US (USW00003928), 5.8 miles from the place internal point.

For Wichita, January maximum/minimum normals are 43.9°F/22.5°F and July reports 92.6°F/70.4°F; July precipitation is 3.98 inches, with a 22.2°F normal daily range.

These Wichita monthly normals provide climate context—not Manual J design temperatures, record temperatures, or equipment-selection conditions.

For broader published Kansas context, consult the Kansas AC sizing guide while interpreting Wichita’s climate frame. For this Wichita address, that statewide page cannot replace the project load and delivery analysis.

Hypothetical example: a slab addition attached to a crawlspace house

The example attaches a glass-heavy slab room to a crawlspace house. A single added branch competes with original bedrooms, and the doorway acts as the only return. The late-afternoon complaint could reflect solar load, inadequate supply, no return, trunk pressure or several at once. A larger replacement leaves those variables entangled and may worsen cycling in the original rooms.

Hypothetical example. This addition is a standalone reasoning case and is not evidence about Wichita’s housing stock.

  • Floor area: approximately 1,720 ft² after addition
  • Construction: 1950s one-story house with a later enclosed sunroom
  • Building inputs: glass-heavy west addition on slab, crawlspace under the original house, one field-added supply branch and no dedicated return in the new room
  • HVAC: older central furnace and AC; a contractor proposes a larger replacement to address the addition
  • Complaint: the original bedrooms lose airflow while the addition remains warm in late afternoon
  • Diagnostic question: Calculate the addition and complete its air loop before deciding whether the original system lacks equipment capacity.

The 1,700-square-foot sizing comparison offers a floor-area comparison for Wichita, not a capacity answer. This hypothetical 1950s one-story house with a later enclosed sunroom still requires its own construction, exposure, infiltration and duct inputs.

Build the addition load surface by surface

Calculate every surface with the correct adjacent condition. The original floor over crawlspace and the addition slab have different boundaries; the former exterior wall may now divide conditioned spaces. Enter roof, wall, glass, infiltration and occupancy for the sunroom itself. Then inspect its peak hour and sensible/latent makeup instead of applying a square-foot multiplier to the existing block load.

Separate slab edge from crawlspace boundary

Model slab perimeter and below-grade assumptions separately from the original framed floor above crawlspace. Copying the older room’s floor construction into the addition can distort both heating and cooling results.

Calculate glass by direction and shade

Enter each glazed face by orientation, product properties and exterior shade. West exposure needs its own timing. A single aggregate window area erases the late-day pattern that occupants actually report.

Use Manual S after the combined load is corrected

Manual S follows the corrected original-house and addition loads. Compare matched sensible and total capacity at project conditions and examine minimum output for times when the glass room is not peaking. The unit cannot be selected as if every room reaches maximum together. If an addition-specific solution is considered, its operating range and controls still need a calculated load rather than a catalog guess. For Wichita, sensible and latent loads remain separate entries: sensible output addresses temperature change, while latent output addresses moisture removal. For this Wichita analysis, neither value is inferred from nominal capacity.

Branch competition can be demonstrated with two measurements: original-bedroom delivery before and after the sunroom branch is opened to its target. If bedroom airflow falls below its calculated need, the trunk or fitting arrangement—not outdoor-unit size—is the immediate constraint. That evidence supports a specific duct remedy or a separate conditioning strategy.

Test whether the original trunk can serve another branch

Test the existing trunk before reserving air for another branch. Measure or model available static pressure, fitting losses and the critical original run. The new branch target comes from the addition load, not from the takeoff diameter chosen in the field. If the trunk cannot support that flow, enlarging the branch may simply divert air from bedrooms and reproduce the reported complaint in a different place.

Give the addition a deliberate return path

Provide a return route that works when doors and furnishings are in normal positions. Options may include a dedicated return or a calculated transfer path; the doorway should not be assumed adequate merely because air can be felt moving through it. Check pressure relative to the house and outdoors. A supply-only addition can become positively pressurized while the original return draws replacement air elsewhere.

Return-path acceptance should include pressure across the connecting doorway in ordinary use. A transfer opening hidden by furniture or a door that owners routinely close cannot be treated as dependable. The final plan must identify a durable path and show that the addition does not drive air into leaks while the main return pulls elsewhere.

Coordinate mechanical permit and field acceptance evidence

Coordinate the mechanical permit and inspection path with technical acceptance, while keeping their purposes distinct. Commission the added loop by recording total static, trunk and branch delivery, return behavior, room temperature response and equipment operation during a relevant solar period. Administrative approval does not supply a load calculation, and a load report does not waive local requirements.

Return to the connecting doorway after balancing. If the addition needs that opening to move a large uncontrolled stream of air, the design has not yet created an independent, measurable room loop.

Similar Posts